Thu Jan 12 2023 10:27:35 GMT+0000 (Coordinated Universal Time)

Feature:Viewing summary of heating zones in different zones with the ability to add more 6

Ticket: https://sero-digital.atlassian.net/browse/IES-356

Scenario:go back to the heating system selection screen
4

Given I am a BEE installer in a home 2s 508ms

And I configure the BEE until "Configure Heating Zone" 11s 540ms
heatingSystem TempSensorLocation TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

When I go back to previous screen 77ms

Then I am on the "heating system type screen" 7ms

Scenario Outline:summary of the zone shown
4

Given I am a BEE installer in a home 2s 882ms

And I configure the BEE until "Configure Heating Zone" 12s 77ms
heatingSystem TempSensorLocation TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

When I have selected all the devices in a boiler heating zone 260ms
zoneID zone TempDial TempSensor Relay Continue
whole_home Whole Home Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

Then I see the details of the zone are summarised on this page 93ms
zoneID zone TempDial TempSensor Relay
whole_home Whole Home Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1

Scenario Outline:Next screen after summary of zone
6

Given I am a BEE installer in a home 2s 531ms

And I configure the BEE until "Configure Heating Zone" 12s 654ms
heatingSystem TempSensorLocation TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

Given I have selected all the devices in a boiler heating zone 282ms
zone TempDial TempSensor Relay Continue
Whole Home Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

And I am on the "assign boiler heating zones summary screen" 29ms

When I continue 111ms

Then I am on the "hot water source screen" 528ms

Scenario:add up to 4 heating zones
4

Given I am a BEE installer in a home 2s 321ms

And I configure the BEE until "Configure Heating Zone" 11s 635ms
heatingSystem TempSensorLocation TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

When I have selected all the devices in a boiler heating zone 273ms
zone TempDial TempSensor Relay Continue Success
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 5 true true

Then I can add another zone up to a maximum of 4 zones 1s 97ms
zone TempDial TempSensor Relay Continue AddButton
Kitchen Thermokon WRF06 - Kitchen Thermokon WRF06 - Kitchen Relay 1 true enabled
Ground Floor Thermokon WRF06 - Ground Floor Thermokon WRF06 - Ground Floor Relay 2 true enabled
First Floor Thermokon WRF06 - First Floor Thermokon WRF06 - First Floor Relay 3 true disabled

Scenario Outline:add button disabled when whole home zone is configured
4

Given I am a BEE installer in a home 2s 514ms

And I configure the BEE until "Configure Heating Zone" 11s 400ms
heatingSystem TempSensorLocation TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

When I have selected all the devices in a boiler heating zone 186ms
zone TempDial TempSensor Relay Continue
Whole Home Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

Then the add heating zone button should be disabled 11ms

Scenario Outline:edit previously configured zone
5

Given I am a BEE installer in a home 2s 285ms

And I configure the BEE until "Configure Heating Zone" 11s 11ms
heatingSystem TempSensorLocation TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

Given I have selected all the devices in a boiler heating zone 266ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

When I am editing the newly configured zone 91ms
zone
living_room

Then I am in the edit heating zone screen for the newly configured zone "living_room" 9ms

Feature:Add Heat Pump Heating Zone 2

Ticket: https://sero-digital.atlassian.net/browse/IES-879
Ticket: https://sero-digital.atlassian.net/browse/IES-1333

Scenario:Cannot proceed to next screen without confirming IP address
5

Given I am a BEE installer in a home 2s 50ms

And I configure the BEE until "Heating Zones Summary" 10s 190ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I have configured a heat pump heating zone 31ms
Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControlDescription
First Floor Thermokon WRF06 - Living Room Heat pump zone 2 Heat pump zone 2

When I do not check the IP address check box 16ms

Then the continue button is disabled 5ms

Scenario:Proceed to next screen after confirm IP address
6

Given I am a BEE installer in a home 2s 677ms

And I configure the BEE until "Heating Zones Summary" 10s 225ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I have configured a heat pump heating zone 36ms
Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControlDescription
First Floor Thermokon WRF06 - Living Room Heat pump zone 2 Heat pump zone 2

When I check the IP address check box 49ms

Then the continue button is enabled 8ms

And I continue 94ms

Feature:As a BEE installer I want to access a digital application to help me set-up and commission a BEE in order to complete a full and reliable installation. 3

Ticket: https://sero-digital.atlassian.net/browse/IES-283

@smoke
Scenario Outline:BEE is configured
7

Given I am a BEE installer in a home 2s 153ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 263ms
heatingSystem meterType
Boiler with hot water cylinder inlineMeter

And I configure the BEE until "Complete Installation" 11s 964ms
heatingSystem hotWaterSystem meterType Zone
Boiler with hot water cylinder System boiler inlineMeter Living Room

When the BEE is configured 66ms

Then the BEE configuration has rules 5ms
id
1

And the BEE configuration has devices 3ms
id
1

And the BEE configuration has schedules 13ms
id
1

@smoke
Scenario Outline:BEE is configured
7

Given I am a BEE installer in a home 2s 239ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 237ms
heatingSystem meterType
Boiler with hot water cylinder currentTransformerMeter

And I configure the BEE until "Complete Installation" 12s 504ms
heatingSystem hotWaterSystem meterType Zone
Boiler with hot water cylinder System boiler currentTransformerMeter Living Room

When the BEE is configured 47ms

Then the BEE configuration has rules 7ms
id
2

And the BEE configuration has devices 6ms
id
2

And the BEE configuration has schedules 2ms
id
2

@smoke
Scenario Outline:BEE is configured
7

Given I am a BEE installer in a home 2s 433ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 203ms
heatingSystem meterType
MasterTherm heat pump currentTransformerMeter

And I configure the BEE until "Complete Installation" 12s 571ms
heatingSystem hotWaterSystem meterType Zone
MasterTherm heat pump Immersion heater currentTransformerMeter Living Room

When the BEE is configured 65ms

Then the BEE configuration has rules 9ms
id
3

And the BEE configuration has devices 3ms
id
3

And the BEE configuration has schedules 1ms
id
3

Feature:Configure Boiler Heating Zone 2

Ticket: https://sero-digital.atlassian.net/browse/IES-695

Scenario:Continue after selecting all devices
5

Given I am a BEE installer in a home 2s 470ms

And I configure the BEE until "Configure Heating Zone" 10s 964ms
heatingSystem
Boiler with hot water cylinder

Given I have selected all the devices in a boiler heating zone 138ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 false

When I continue 94ms

Then I am on the "assign boiler heating zones summary screen" 5ms

Scenario:Zone, Temperature Dials, Temperature Sensors and Control options become disabled after being selected once
5

Given I am a BEE installer in a home 2s 197ms

And I configure the BEE until "Configure Heating Zone" 10s 952ms
heatingSystem
Boiler with hot water cylinder

Given I have selected all the devices in a boiler heating zone 447ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

When I configure a new boiler heating zone 81ms

Then the selected zone, temperature dial, temperature sensor, and control option should be disabled 4ms
zone TempDial TempSensor Relay
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1

Feature:Configure Heat Pump Heating Zone 4

Ticket: https://sero-digital.atlassian.net/browse/IES-880

Scenario:Continue after selecting all devices
4

Given I am a BEE installer in a home 2s 302ms

And I configure the BEE until "Configure Heating Zone" 11s 870ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
MasterTherm heat pump Living Room C1 1
Ground Floor C2 2

Given I have selected all the devices in a heat pump heating zone 295ms
zone TempDial TempSensor TempSensorLocation
Whole Home Thermokon WRF06 - Living Room HC2 Living Room

Then I am on the "assign heat pump heating zones summary screen" 1ms

Scenario:Prevent the same zone being used twice
5

Ticket: https://sero-digital.atlassian.net/browse/IES-1317

Given I am a BEE installer in a home 2s 271ms

And I configure the BEE until "Configure Heating Zone" 11s 567ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
MasterTherm heat pump Living Room C1 1
Ground Floor C2 2

Given I have selected all the devices in a heat pump heating zone 312ms
zone TempDial TempSensor TempSensorLocation
Kitchen Thermokon WRF06 - Living Room HC2 Living Room

When I configure a new heat pump heating zone 78ms

Then I cannot use that heat pump zone for another home zone 35ms
zone HeatPumpHeatingControl
Living Room HC2

Scenario:Editing a heat pump
7

Given I am a BEE installer in a home 2s 274ms

And I configure the BEE until "Configure Heating Zone" 11s 220ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
MasterTherm heat pump Living Room C1 1
Ground Floor C2 2

Given I have selected all the devices in a heat pump heating zone 186ms
zone TempDial TempSensor TempSensorLocation
Whole Home Thermokon WRF06 - Living Room HC2 Living Room

And I edit the "whole_home" heat pump heating zone 283ms
zone TempDial TempSensor TempSensorLocation
Kitchen Thermokon WRF06 - Living Room HC1 Kitchen

When I continue and wait 631ms

Then the BEE is configured 58ms

And the BEE configuration has rules 5ms

Scenario:Delete a heat pump
9

Given I am a BEE installer in a home 2s 254ms

And I configure the BEE until "Configure Heating Zone" 10s 815ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
MasterTherm heat pump Living Room C1 1
Ground Floor C2 2

Given I have selected all the devices in a heat pump heating zone 632ms
zone TempDial TempSensor TempSensorLocation
Whole Home Thermokon WRF06 - Living Room HC2 Living Room
Ground Floor Thermokon WRF06 - Ground Floor HC1 Ground Floor

And I continue and wait 611ms

And I go back to previous screen 126ms

And I delete the "whole_home" heat pump heating zone 559ms

When I continue and wait 664ms

Then the BEE is configured 82ms

And the BEE configuration has rules 2ms

Feature:Select the type of Hot Water heating system 11

Ticket: https://sero-digital.atlassian.net/browse/IES-853

Scenario:Continue to next screen after selecting Heat Pump as hot water source and confirming IP address
11

Given I am a BEE installer in a home 2s 604ms

And I configure the BEE until "Configure Hot Water" 12s 303ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I choose a hot water source 31ms
hotWaterSource
Heat pump

And I select whether there is an immersion heater 20ms
isImmersionHeater
Yes

And I select the relay that controls the immersion heater 20ms
immersionHeaterRelay
Relay 3

And I check the IP address confirmation box 47ms

When I continue and wait 1s 243ms

Then the BEE is configured 46ms

And the BEE configuration has rules 2ms

And the BEE configuration has devices 2ms

And I am on the 'bee successfully updated screen' < 1ms

Scenario:Can't continue to next screen after selecting Heat Pump as hot water source and not confirming IP address
8

Given I am a BEE installer in a home 2s 874ms

And I configure the BEE until "Configure Hot Water" 11s 389ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I choose a hot water source 27ms
hotWaterSource
Heat pump

And I select whether there is an immersion heater 27ms
isImmersionHeater
Yes

And I select the relay that controls the immersion heater 21ms
immersionHeaterRelay
Relay 3

When I do not check the IP address check box 12ms

And the continue button is disabled 3ms

Then I am on the "hot water source screen" 142ms

Scenario Outline:Configured hot water source is persisted
10

Given I am a BEE installer in a home 2s 554ms

And I configure the BEE until "Configure Hot Water" 11s 710ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 136ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump Yes Relay 3

And I continue and wait 1s 599ms

And the BEE is configured 51ms

And the BEE configuration has rules 3ms
id
1

And I am on the 'bee successfully updated screen' 1ms

When I go back to previous screen 130ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 76ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump Yes Relay 3

Scenario Outline:Configured hot water source is persisted
10

Given I am a BEE installer in a home 2s 570ms

And I configure the BEE until "Configure Hot Water" 11s 495ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 128ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump No

And I continue and wait 1s 426ms

And the BEE is configured 45ms

And the BEE configuration has rules 2ms
id
2

And I am on the 'bee successfully updated screen' 3ms

When I go back to previous screen 44ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 63ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump No

Scenario Outline:Configured hot water source is persisted
10

Given I am a BEE installer in a home 2s 225ms

And I configure the BEE until "Configure Hot Water" 11s 50ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 138ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 Yes Relay 4

And I continue and wait 1s 417ms

And the BEE is configured 50ms

And the BEE configuration has rules 2ms
id
3

And I am on the 'bee successfully updated screen' < 1ms

When I go back to previous screen 104ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 54ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 Yes Relay 4

Scenario Outline:Configured hot water source is persisted
10

Given I am a BEE installer in a home 2s 129ms

And I configure the BEE until "Configure Hot Water" 11s 327ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 68ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 No

And I continue and wait 1s 201ms

And the BEE is configured 55ms

And the BEE configuration has rules 2ms
id
4

And I am on the 'bee successfully updated screen' < 1ms

When I go back to previous screen 80ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 40ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 No

Scenario Outline:Configured hot water source is persisted
10

Given I am a BEE installer in a home 2s 134ms

And I configure the BEE until "Configure Hot Water" 11s 90ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 69ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Immersion heater Relay 3 undefined

And I continue and wait 1s 610ms

And the BEE is configured 60ms

And the BEE configuration has rules 2ms
id
5

And I am on the 'bee successfully updated screen' 2ms

When I go back to previous screen 83ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 50ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Immersion heater Relay 3 undefined

Scenario Outline:Can edit a previously configured hot water source
12

Given I am a BEE installer in a home 2s 265ms

And I configure the BEE until "Configure Hot Water" 11s 861ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 264ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump Yes Relay 3

And I continue and wait 947ms

And I go back to previous screen 91ms

And I configure a hot water source 115ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump No

And I continue and wait 1s 220ms

And the BEE is configured 50ms

And the BEE configuration has rules 2ms
id
1

When I go back to previous screen 41ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 48ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump No

Scenario Outline:Can edit a previously configured hot water source
12

Given I am a BEE installer in a home 2s 108ms

And I configure the BEE until "Configure Hot Water" 11s 279ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 254ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump Yes Relay 3

And I continue and wait 750ms

And I go back to previous screen 51ms

And I configure a hot water source 119ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 Yes Relay 4

And I continue and wait 1s 473ms

And the BEE is configured 79ms

And the BEE configuration has rules 1ms
id
2

When I go back to previous screen 49ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 57ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 Yes Relay 4

Scenario Outline:Can edit a previously configured hot water source
12

Given I am a BEE installer in a home 2s 275ms

And I configure the BEE until "Configure Hot Water" 11s 379ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 187ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump Yes Relay 3

And I continue and wait 979ms

And I go back to previous screen 55ms

And I configure a hot water source 86ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 No

And I continue and wait 1s 513ms

And the BEE is configured 39ms

And the BEE configuration has rules 1ms
id
3

When I go back to previous screen 56ms

Then I am on the "hot water source screen" < 1ms

And the previously configured hot water source is displayed 35ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
System boiler Relay 3 No

Scenario Outline:Can edit a previously configured hot water source
12

Given I am a BEE installer in a home 2s 486ms

And I configure the BEE until "Configure Hot Water" 11s 158ms
heatingSystem Zone HeatPumpTempDial HeatPumpTempSensor HeatPumpHeatingControl
MasterTherm heat pump First Floor Thermokon WRF06 - Living Room HC2 HC2

Given I configure a hot water source 114ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Heat pump Yes Relay 3

And I continue and wait 992ms

And I go back to previous screen 52ms

And I configure a hot water source 60ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Immersion heater Relay 3 undefined

And I continue and wait 1s 962ms

And the BEE is configured 71ms

And the BEE configuration has rules 2ms
id
4

When I go back to previous screen 82ms

Then I am on the "hot water source screen" 1ms

And the previously configured hot water source is displayed 77ms
hotWaterSource hotWaterSourceRelayAddress isImmersionHeater immersionHeaterRelay
Immersion heater Relay 3 undefined

Feature:Electricity Meters - inline meters - sharky meters 1

Ticket: https://sero-digital.atlassian.net/browse/IES-742

Scenario:All fields required - -
4

Given I am a BEE installer in a home 2s 2ms

And I configure the BEE until "Add Heat Flow Meter" 8s 632ms
meterType
inlineMeter

When I continue with the configuration of a sharky meter after configuring an inline meter 94ms

Then I cannot continue without completing all heat flow meter fields 4ms

Feature:Configuration of temperature monitoring device 7

Ticket: https://sero-digital.atlassian.net/browse/IES-606

Scenario:Return back to Sharky configuration screen from the Thermokon WRF04
4

Given I am a BEE installer in a home 1s 981ms

Given I configure the BEE until "Configure Thermostat Sensor" 10s 130ms

When I go back to previous screen 117ms

Then I am on the "thermostat model screen" 1ms

Scenario Outline:Proceed to the next screen
5

Given I am a BEE installer in a home 2s 250ms

Given I configure the BEE until "Configure Thermostat Sensor" 11s 62ms
TempSensorModel
regin

And I have clicked the confirmation tick-box 139ms

When I continue 156ms

Then I am on the "heating system type screen" 1ms

Scenario Outline:Proceed to the next screen
5

Given I am a BEE installer in a home 2s 330ms

Given I configure the BEE until "Configure Thermostat Sensor" 9s 806ms
TempSensorModel
novos3

And I have clicked the confirmation tick-box 79ms

When I continue 166ms

Then I am on the "heating system type screen" 1ms

Scenario Outline:Proceed to the next screen
5

Given I am a BEE installer in a home 2s 486ms

Given I configure the BEE until "Configure Thermostat Sensor" 9s 706ms
TempSensorModel
wrf04

And I have clicked the confirmation tick-box 116ms

When I continue 86ms

Then I am on the "heating system type screen" < 1ms

Scenario Outline:Configure different types of temperature monitoring
4

Given I am a BEE installer in a home 2s 441ms

Given I configure the BEE until "Configure Hot Water" 11s 815ms
TempSensorModel heatingSystem TempSensorModelDescription TempSensorLocation Zone
regin Boiler with hot water cylinder Regin CTHRC - Living Room Living Room First Floor

When the BEE is configured 60ms

Then the BEE configuration has rules 1ms
id
1

Scenario Outline:Configure different types of temperature monitoring
4

Given I am a BEE installer in a home 2s 445ms

Given I configure the BEE until "Configure Hot Water" 10s 370ms
TempSensorModel heatingSystem TempSensorModelDescription TempSensorLocation Zone
novos3 Boiler with hot water cylinder Thermokon Novos 3 - Living Room Living Room First Floor

When the BEE is configured 57ms

Then the BEE configuration has rules 2ms
id
2

Scenario Outline:Configure different types of temperature monitoring
4

Given I am a BEE installer in a home 2s 377ms

Given I configure the BEE until "Configure Hot Water" 10s 448ms
TempSensorModel heatingSystem TempSensorModelDescription TempSensorLocation Zone
wrf04 Boiler with hot water cylinder Thermokon WRF04 - Living Room Living Room First Floor

When the BEE is configured 56ms

Then the BEE configuration has rules 2ms
id
3

Feature:Configure Thermostat Dial 1

Ticket: https://sero-digital.atlassian.net/browse/IES-854
Ticket: https://sero-digital.atlassian.net/browse/IES-1239
Ticket: https://sero-digital.atlassian.net/browse/IES-1240

Scenario:Saved WRF06 dial channel configuration shown when editing
5

Given I am a BEE installer in a home 2s 287ms

And I configure the BEE until "Configure Thermostat Dial" 8s 800ms

When I configure a Thermokon WRF06 dial 245ms

When I click on one of the WRF06 devices listed 161ms
location
bedroom_1

Then the previously entered channel "Comm 1" is displayed 21ms

Feature:Edit & Delete Thermokon WRF06 configuration 7

Ticket: https://sero-digital.atlassian.net/browse/IES-1207

Scenario:previous saved configuration shown in edit
5

Given I am a BEE installer in a home 2s 250ms

And I configure the BEE until "Add Thermostat Dial" 9s 169ms

And I have configured one or more Thermokon WRF06 devices 685ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C3 6

And I click on one of the WRF06 devices listed 105ms
location
kitchen

Then I am taken to the screen to edit a WRF06 configuration 13ms
location locationDescription device mchannel maddress
kitchen Kitchen Thermokon WRF06 C2 4

Scenario:Return to summary screen without saving the edit
7

Given I am a BEE installer in a home 2s 347ms

And I configure the BEE until "Add Thermostat Dial" 9s 119ms

And I have configured one or more Thermokon WRF06 devices 585ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C3 6

And I click on one of the WRF06 devices listed 61ms
location
kitchen

Given I have changed the configuration 112ms
locationDescription device mchannel maddress
First Floor Thermokon WRF06 C3 16

When I go back to previous screen 85ms

Then any changes are discarded 10ms
locationDescription location device mchannel maddress
Kitchen kitchen Thermokon WRF06 C2 4

Scenario:Return to summary screen
6

Given I am a BEE installer in a home 2s 192ms

And I configure the BEE until "Add Thermostat Dial" 9s 576ms

And I have configured one or more Thermokon WRF06 devices 492ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C3 6

And I click on one of the WRF06 devices listed 75ms
location
kitchen

When I go back to previous screen 60ms

Then I get a summary of all WRF06 devices that have been configured 5ms
location locationDescription device mchannel maddress
kitchen Kitchen Thermokon WRF06 C2 4

Scenario:Save edit and return to summary page
7

Given I am a BEE installer in a home 2s 270ms

And I configure the BEE until "Add Thermostat Dial" 9s 56ms

And I have configured one or more Thermokon WRF06 devices 603ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C3 6

And I click on one of the WRF06 devices listed 55ms
location
kitchen

Given I have changed the configuration 90ms
locationDescription device mchannel maddress
First Floor Thermokon WRF06 C3 17

When I continue 75ms

Then I get a summary of all WRF06 devices that have been configured 6ms
location locationDescription device mchannel maddress
first_floor First Floor Thermokon WRF06 C3 17

Scenario:Delete device
6

Given I am a BEE installer in a home 2s 146ms

And I configure the BEE until "Add Thermostat Dial" 9s 106ms

And I have configured one or more Thermokon WRF06 devices 513ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C3 6

And I click on one of the WRF06 devices listed 102ms
location
kitchen

When I click Delete Device 490ms

Then the configuration of the device is removed 4ms
location
kitchen

Scenario:Return to summary page after delete
6

Given I am a BEE installer in a home 2s 282ms

And I configure the BEE until "Add Thermostat Dial" 9s 221ms

And I have configured one or more Thermokon WRF06 devices 606ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C3 6

And I click on one of the WRF06 devices listed 98ms
location
kitchen

When I click Delete Device 444ms

Then I get a summary of all WRF06 devices that have been configured 5ms
location locationDescription device mchannel maddress
living_room Living Room Thermokon WRF06 C3 6

Scenario:Cannot selected location for another WRF06 device
5

Given I am a BEE installer in a home 2s 319ms

And I configure the BEE until "Add Thermostat Dial" 9s 123ms

And I have configured one or more Thermokon WRF06 devices 617ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C3 6

And I click on one of the WRF06 devices listed 80ms
location
kitchen

Then I cannot select a location that has been used for another WRF06 device 6ms
locationDescription
Living Room

Feature:Edit & Delete Thermokon WRF06 configuration 1

Ticket: https://sero-digital.atlassian.net/browse/IES-1207

Scenario:Can not select location assigned to existing zone or WHOLE HOME
7

Given I am a BEE installer in a home 2s 254ms

And I configure the BEE until "Configure Hot Water" 10s 926ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room C1 1

And I click the home button 58ms

And I configure the BEE until "Add Thermostat Dial" 7s 174ms
heatFlowMeterCircuit
heating

Given I have configured one or more Thermokon WRF06 devices 247ms
locationDescription mchannel maddress
Kitchen C2 4

When I click on one of the WRF06 devices listed 90ms
location
kitchen

Then I cannot select the location 18ms
location locationDescription
living_room Living Room
whole_home Whole Home

Feature:Thermokon WRF06 summary screen 3

Ticket: https://sero-digital.atlassian.net/browse/IES-1193

Scenario:Display of summary of all WRF06 devices
4

Given I am a BEE installer in a home 2s 262ms

And I configure the BEE until "Add Thermostat Dial" 9s 519ms

When I have configured one or more Thermokon WRF06 devices 502ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C4 6

Then I get a summary of all WRF06 devices that have been configured 10ms
location locationDescription device mchannel maddress
kitchen Kitchen Thermokon WRF06 C2 4
living_room Living Room Thermokon WRF06 C4 6

Scenario:Return from WRF04 configuration screen
8

Given I am a BEE installer in a home 2s 142ms

And I configure the BEE until "Add Thermostat Dial" 8s 507ms

When I have configured one or more Thermokon WRF06 devices 398ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C4 6

Given I continue 57ms

And I select the "Thermokon WRF04" thermostat 76ms

And I am on the "config thermokon wrf04 screen" < 1ms

When I go back 2 screens 125ms

Then I get a summary of all WRF06 devices that have been configured 8ms
location locationDescription device mchannel maddress
kitchen Kitchen Thermokon WRF06 C2 4
living_room Living Room Thermokon WRF06 C4 6

Scenario:Edit WRF06 configuration
5

Given I am a BEE installer in a home 2s 347ms

And I configure the BEE until "Add Thermostat Dial" 9s 734ms

When I have configured one or more Thermokon WRF06 devices 459ms
locationDescription mchannel maddress
Kitchen C2 4
Living Room C4 6

When I click on one of the WRF06 devices listed 50ms
location
kitchen

Then I am taken to the screen to edit a WRF06 configuration 6ms
location locationDescription device mchannel maddress
kitchen Kitchen Thermokon WRF06 C2 4

Feature:Devices connected check 5

Ticket: https://sero-digital.atlassian.net/browse/IES-291

Scenario Outline:Go back to previous screen to version updated screen
6

Given I am a BEE installer in a home 2s 193ms

Given the BEE is running on the latest firmware and the peripherals connected to the BEE have been reported 180ms
healthcheck heatingSystem hotWaterSystem meterType
healthy Boiler with hot water cylinder System boiler inlineMeter

And I configure the BEE until "Peripheral Health Checks" 11s 918ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

And I am on the "check peripherals screen" 9ms

When I go back to previous screen 69ms

Then I am on the "bee successfully updated screen" 2ms

Scenario Outline:Display of status of connected peripheral
5

Given I am a BEE installer in a home 2s 207ms

Given the BEE is running on the latest firmware and the peripherals connected to the BEE have been reported 229ms
healthcheck heatingSystem hotWaterSystem meterType
healthy Boiler with hot water cylinder System boiler inlineMeter

And I configure the BEE until "Peripheral Health Checks" 12s 465ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

And I am on the "check peripherals screen" 1ms

Then the result on the screen the peripheral shown 51ms
status color device index
Connected rgb(14, 190, 53) 5 C1 - IEM2055 0

Scenario Outline:Display of status of non-connected peripheral
5

Given I am a BEE installer in a home 2s 302ms

Given the BEE is running on the latest firmware and the peripherals connected to the BEE have been reported 264ms
healthcheck heatingSystem hotWaterSystem meterType
unhealthy Boiler with hot water cylinder System boiler inlineMeter

And I configure the BEE until "Peripheral Health Checks" 11s 389ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

And I am on the "check peripherals screen" 1ms

Then the result on the screen the peripheral shown 55ms
status color device index
Responded with error rgb(241, 0, 0) Living Room - WRF06 2

Scenario Outline:Can proceed to next screen if passing device check
5

Given I am a BEE installer in a home 2s 5ms

Given the BEE is running on the latest firmware and the peripherals connected to the BEE have been reported 189ms
healthcheck heatingSystem hotWaterSystem meterType
healthy Boiler with hot water cylinder System boiler inlineMeter

And I configure the BEE until "Peripheral Health Checks" 12s 464ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

And I am on the "check peripherals screen" 1ms

Then the continue button is enabled 4ms

Scenario Outline:Cannot proceed to next screen
5

Given I am a BEE installer in a home 2s 109ms

Given the BEE is running on the latest firmware and the peripherals connected to the BEE have been reported 162ms
healthcheck heatingSystem hotWaterSystem meterType
some-unhealthy Boiler with hot water cylinder System boiler inlineMeter

And I configure the BEE until "Peripheral Health Checks" 12s 901ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

And I am on the "check peripherals screen" < 1ms

Then the continue button is disabled 4ms

Feature:Editing & deleting a Heating Zone for a boiler 4

Ticket: https://sero-digital.atlassian.net/browse/IES-882

Scenario:Back button brings user back to previous page
5

Given I am a BEE installer in a home 2s 252ms

And I configure the BEE until "Heating Zones Summary" 10s 769ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress Zone
Boiler with hot water cylinder Living Room C1 1 Living Room
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

Given I am editing the newly configured zone 65ms
zone
living_room

When I go back to previous screen 66ms

Then I am on the "assign boiler heating zones summary screen" < 1ms

Scenario:Return to summary page after a zone is succesfully deleted
5

Given I am a BEE installer in a home 2s 282ms

And I configure the BEE until "Heating Zones Summary" 12s 250ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress Zone
Boiler with hot water cylinder Living Room C1 1 Living Room
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

Given I am editing the newly configured zone 117ms
zone
living_room

When I click the Delete Heating Zone button 474ms

Then I am on the "assign boiler heating zones summary screen" 1ms

Scenario:Save the change
5

Given I am a BEE installer in a home 1s 988ms

And I configure the BEE until "Heating Zones Summary" 11s 312ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress Zone
Boiler with hot water cylinder Living Room C1 1 Living Room
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

Given I am editing the newly configured zone 59ms
zone
living_room

When I edit a boiler heating zone 142ms
zoneDescription TempDial TempSensor Relay Continue
Kitchen Thermokon WRF06 - Kitchen Thermokon WRF06 - Kitchen Relay 3 true

Then I am on the "assign boiler heating zones summary screen" 1ms

Scenario:Change is saved succesfully
7

Given I am a BEE installer in a home 2s 135ms

And I configure the BEE until "Heating Zones Summary" 11s 52ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress Zone
Boiler with hot water cylinder Living Room C1 1 Living Room
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

Given I am editing the newly configured zone 57ms
zone
living_room

And I edit a boiler heating zone 165ms
zoneDescription TempDial TempSensor Relay Continue
Kitchen Thermokon WRF06 - Kitchen Thermokon WRF06 - Kitchen Relay 3 true

When I continue and wait 623ms

Then the BEE is configured 63ms

And the BEE configuration has rules 2ms

Feature:Edit a previously configured heating system 8

Ticket: https://sero-digital.atlassian.net/browse/IES-1354

Scenario Outline:Change assigned heating system when switching between boiler heating zones
14

Given I am a BEE installer in a home 2s 95ms

And I configure the BEE until "Configure Heating System" 8s 983ms

Given I choose from one of the heating systems on the list 133ms
HeatingSystem
Boiler with hot water cylinder

And I configure a new boiler heating zone 60ms

And I have selected all the devices in a boiler heating zone 258ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

And I continue and wait 666ms

And I am on the 'hot water source screen' 228ms

And I go back 3 screens 191ms

And I am on the "heating system type screen" 1ms

And I choose from one of the heating systems on the list 109ms
HeatingSystem
Combi boiler

When I continue and wait 631ms

And I am on the 'hot water source screen' 251ms

Then the BEE is configured 48ms

And the BEE configuration has rules 3ms
id
(boiler with hot water cylinder to combi boiler)

Scenario Outline:Change assigned heating system when switching between boiler heating zones
14

Given I am a BEE installer in a home 2s 127ms

And I configure the BEE until "Configure Heating System" 9s 307ms

Given I choose from one of the heating systems on the list 217ms
HeatingSystem
Combi boiler

And I configure a new boiler heating zone 107ms

And I have selected all the devices in a boiler heating zone 313ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

And I continue and wait 891ms

And I am on the 'hot water source screen' 53ms

And I go back 3 screens 208ms

And I am on the "heating system type screen" < 1ms

And I choose from one of the heating systems on the list 131ms
HeatingSystem
Boiler with hot water cylinder

When I continue and wait 571ms

And I am on the 'hot water source screen' 251ms

Then the BEE is configured 51ms

And the BEE configuration has rules 2ms
id
(combi boiler to boiler with hot water cylinder)

Scenario Outline:Change assigned heating system when switching from a boiler heating zone to a heat pump heating zone
16

Given I am a BEE installer in a home 2s 345ms

And I configure the BEE until "Configure Heating System" 9s 289ms

Given I choose from one of the heating systems on the list 134ms
HeatingSystem
Boiler with hot water cylinder

And I configure a new boiler heating zone 86ms

And I have selected all the devices in a boiler heating zone 265ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

And I continue and wait 614ms

And I am on the 'hot water source screen' 260ms

And I go back 3 screens 154ms

And I am on the "heating system type screen" < 1ms

And I choose from one of the heating systems on the list 80ms
HeatingSystem
MasterTherm heat pump

And I configure a new heat pump heating zone 55ms

And I have selected all the devices in a heat pump heating zone 220ms
zone TempDial TempSensor TempSensorLocation
Living Room Thermokon WRF06 - Living Room HC2 Living Room

And I check the IP address check box 12ms

When I continue and wait 614ms

Then the BEE is configured 55ms

And the BEE configuration has rules 2ms

Scenario Outline:Change assigned heating system when switching from a heat pump heating zone to a boiler heating zone
15

Given I am a BEE installer in a home 2s 370ms

And I configure the BEE until "Configure Heating System" 9s 452ms

Given I choose from one of the heating systems on the list 145ms
HeatingSystem
MasterTherm heat pump

And I configure a new heat pump heating zone 76ms

And I have selected all the devices in a heat pump heating zone 301ms
zone TempDial TempSensor TempSensorLocation
Living Room Thermokon WRF06 - Living Room HC2 Living Room

And I continue and wait 639ms

And I am on the 'hot water source screen' 236ms

And I go back 3 screens 141ms

And I am on the "heating system type screen" < 1ms

And I choose from one of the heating systems on the list 72ms
HeatingSystem
Boiler with hot water cylinder

And I configure a new boiler heating zone 58ms

And I have selected all the devices in a boiler heating zone 244ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

When I continue and wait 643ms

Then the BEE is configured 52ms

And the BEE configuration has rules 1ms
id
(mastertherm heat pump to boiler with hot water cylinder)

Scenario Outline:Change assigned heating system when switching from a heat pump heating zone to a boiler heating zone
15

Given I am a BEE installer in a home 2s 272ms

And I configure the BEE until "Configure Heating System" 9s 67ms

Given I choose from one of the heating systems on the list 161ms
HeatingSystem
MasterTherm heat pump

And I configure a new heat pump heating zone 68ms

And I have selected all the devices in a heat pump heating zone 247ms
zone TempDial TempSensor TempSensorLocation
Living Room Thermokon WRF06 - Living Room HC2 Living Room

And I continue and wait 720ms

And I am on the 'hot water source screen' 242ms

And I go back 3 screens 214ms

And I am on the "heating system type screen" < 1ms

And I choose from one of the heating systems on the list 162ms
HeatingSystem
Combi boiler

And I configure a new boiler heating zone 104ms

And I have selected all the devices in a boiler heating zone 357ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

When I continue and wait 702ms

Then the BEE is configured 57ms

And the BEE configuration has rules 3ms
id
(mastertherm heat pump to combi boiler)

Scenario Outline:Remove assigned heating system when switching from a boiler heating zone to heating not controlled by IES
14

Given I am a BEE installer in a home 2s 276ms

And I configure the BEE until "Configure Heating System" 10s 547ms

Given I choose from one of the heating systems on the list 82ms
HeatingSystem
Boiler with hot water cylinder

And I configure a new boiler heating zone 58ms

And I have selected all the devices in a boiler heating zone 183ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

And I continue and wait 629ms

And I am on the 'hot water source screen' 189ms

And I go back 3 screens 148ms

And I am on the "heating system type screen" < 1ms

And I choose from one of the heating systems on the list 88ms
HeatingSystem
Heating not controlled by the IES

And I am on the 'bee successfully updated screen' < 1ms

When I go back to previous screen 76ms

When I choose from one of the heating systems on the list 70ms
HeatingSystem
Boiler with hot water cylinder

Then I do not see the details of the zone summarised on this page 5ms
zoneID
living_room

Scenario Outline:Remove assigned heating system when switching from a boiler heating zone to heating not controlled by IES
14

Given I am a BEE installer in a home 2s 245ms

And I configure the BEE until "Configure Heating System" 9s 884ms

Given I choose from one of the heating systems on the list 103ms
HeatingSystem
Combi boiler

And I configure a new boiler heating zone 53ms

And I have selected all the devices in a boiler heating zone 221ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

And I continue and wait 543ms

And I am on the 'hot water source screen' 245ms

And I go back 3 screens 170ms

And I am on the "heating system type screen" < 1ms

And I choose from one of the heating systems on the list 90ms
HeatingSystem
Heating not controlled by the IES

And I am on the 'bee successfully updated screen' < 1ms

When I go back to previous screen 52ms

When I choose from one of the heating systems on the list 110ms
HeatingSystem
Combi boiler

Then I do not see the details of the zone summarised on this page 7ms
zoneID
living_room

Scenario Outline:Remove assigned heating system when switching from a heat pump heating zone to heating not controlled by IES
14

Given I am a BEE installer in a home 2s 405ms

And I configure the BEE until "Configure Heating System" 10s 512ms

Given I choose from one of the heating systems on the list 87ms
HeatingSystem
MasterTherm heat pump

And I configure a new heat pump heating zone 76ms

And I have selected all the devices in a heat pump heating zone 237ms
zone TempDial TempSensor TempSensorLocation
Living Room Thermokon WRF06 - Living Room HC2 Living Room

And I continue and wait 578ms

And I am on the 'hot water source screen' 255ms

And I go back 3 screens 135ms

And I am on the "heating system type screen" < 1ms

And I choose from one of the heating systems on the list 74ms
HeatingSystem
Heating not controlled by the IES

And I am on the 'bee successfully updated screen' < 1ms

When I go back to previous screen 50ms

When I choose from one of the heating systems on the list 76ms
HeatingSystem
MasterTherm heat pump

Then I do not see the details of the zone summarised on this page 5ms
zoneID
living_room

Feature:Electricity Meters - CT 1

Ticket:https://sero-digital.atlassian.net/browse/IES-572
Ticket:https://sero-digital.atlassian.net/browse/IES-578
Ticket:https://sero-digital.atlassian.net/browse/IES-1061

Scenario:Config Current Transformer Meters
5

Given I am a BEE installer in a home 2s 87ms

And I configure the BEE until "CT Meter Configuration" 6s 762ms
meterType
currentTransformerMeter

Given I config Current Transformer Meters 786ms
Type Description
Whole home Whole home xxx
Regulated Regulated bbb
Unregulated Unregulated ccc
Main incoming supply Main incoming supply Description
Unmeasured unmeasuredDescription

And I continue 77ms

Then I am on the "heat flow meter screen" 534ms

Feature:Select Make/Model of CT electricity meter 2

Ticket:https://sero-digital.atlassian.net/browse/IES-1080

Scenario Outline:Select CT Meter Make/Model - schneider_iem3455
4

Given I am a BEE installer in a home 2s 12ms

And I configure the BEE until "Select CT Meter Make/Model" 6s 786ms
meterType
currentTransformerMeter

When I have selected the meter model "schneider_iem3455" 82ms

Then I go to the the CT Meter configuration page 1ms

Scenario Outline:return to choose type of meter page
4

Given I am a BEE installer in a home 1s 894ms

And I configure the BEE until "Select CT Meter Make/Model" 6s 454ms
meterType
currentTransformerMeter

When I go back to previous screen 48ms

Then I am on the "choose meter type screen" < 1ms

Feature:ElectricityMeters CT Configured 1

Ticket:https://sero-digital.atlassian.net/browse/IES-1098

Scenario:Review all configurations by navigating from home screen
6

Given I am a BEE installer in a home 2s 131ms

And I configure the BEE until "Add Heat Flow Meter" 7s 188ms
meterType
currentTransformerMeter

Given I click the home button 58ms

And I configure the BEE until "Choose Meter Type" 4s 600ms
meterType
currentTransformerMeter

When I select CT meter 1s 180ms

Then the previous configurations are displayed on all the CT meter configuration screens 261ms

Feature:Electricity Meters - Inline meters 4

Ticket:https://sero-digital.atlassian.net/browse/IES-572

Scenario:All fields required to continue
3

Given I am a BEE installer in a home 2s 143ms

And I configure the BEE until "Configure Inline Meter" 6s 770ms

Then I should only be able to move forward when all required fields have been completed 239ms
device Amperage modbus circuitType
Kitchen 45 5 Regulated

Scenario:Choose inline Meters
4

Given I am a BEE installer in a home 2s 233ms

And I configure the BEE until "Configure Inline Meter" 7s 41ms

When I config inline meter with device name "Kitchen" Amperage 45 and MODBUS 5 and circuit type "Regulated" 264ms

Then the only inline meter shows correct device "Kitchen" information 20ms

Scenario:Delete inline Meters
7

Given I am a BEE installer in a home 2s 134ms

And I configure the BEE until "Configure Inline Meter" 7s 192ms

Given I config inline meter with device name "Kitchen" Amperage 45 and MODBUS 5 and circuit type "Regulated" 327ms

And I add line meter 88ms

And I config inline meter with device name "Living Room" Amperage 63 and MODBUS 6 and circuit type "Regulated" 329ms

When I delete the meter "Living Room" that I have already added to the configuration 524ms

Then "Living Room" is removed from the inline meters 5ms

Scenario:Edit inline Meters
5

Given I am a BEE installer in a home 2s 307ms

And I configure the BEE until "Configure Inline Meter" 6s 524ms

Given I config inline meter with device name "Kitchen" Amperage 45 and MODBUS 5 and circuit type "Regulated" 325ms

When I edit the meter "Kitchen" that I have already added to the configuration renaming the device to "Living Room" 156ms

Then the only inline meter shows correct device "Living Room" information 19ms

Feature:Installation Complete 3

Ticket: https://sero-digital.atlassian.net/browse/IES-1195

Scenario:Go back to previous screen - check peripherals
6

Given I am a BEE installer in a home 2s 158ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 398ms
heatingSystem meterType
Boiler with hot water cylinder inlineMeter

And I configure the BEE until "Complete Installation" 12s 620ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

Given I am on the "installation complete screen" < 1ms

When I go back to previous screen 79ms

Then I am on the "check peripherals screen" 2ms

Scenario:Go to launch screen
6

Given I am a BEE installer in a home 2s 98ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 173ms
heatingSystem meterType
Boiler with hot water cylinder inlineMeter

And I configure the BEE until "Complete Installation" 11s 725ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

Given I am on the "installation complete screen" < 1ms

When I click finish 79ms

Then I am on the "launch screen" < 1ms

Scenario:Address shown on Complete screen
5

Given I am a BEE installer in a home 2s 173ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 452ms
heatingSystem meterType
Boiler with hot water cylinder inlineMeter

And I configure the BEE until "Complete Installation" 11s 618ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

Given I am on the "installation complete screen" 1ms

Then I see the address of the property 18ms
address
2 Barons Court Road

Feature:Firmware Requires Update 3

Ticket:https://sero-digital.atlassian.net/browse/IES-966

Scenario:BEE Requires Update screen shown when earlier than current version
6

Given I am a BEE installer in a home 2s 206ms

When the BEE is running on older firmware and the peripherals connected to the BEE are healthy 1s 165ms

When I configure the BEE until "Firmware Updated" 13s 336ms
hotWaterSystem
System boiler

When I am on the "firmware version check screen" < 1ms

Then the BEE ID will be displayed on the screen 48ms

Then the MAC address will be displayed on the screen 17ms

Scenario:Current BEE firmware version shown in the BEE requires update screen
5

Given I am a BEE installer in a home 2s 396ms

When the BEE is running on older firmware and the peripherals connected to the BEE are healthy 410ms

When I configure the BEE until "Firmware Updated" 11s 258ms
hotWaterSystem
System boiler

Then the firmware is updated 2ms

And the current BEE firmware version "0.9.0" will be displayed on the screen 33ms

Scenario:Return back to previous screen
5

Given I am a BEE installer in a home 2s 139ms

When the BEE is running on older firmware and the peripherals connected to the BEE are healthy 170ms

When I configure the BEE until "Firmware Updated" 11s 851ms
hotWaterSystem
System boiler

When I go back to previous screen 42ms

Then I am on the "hot water source screen" 1ms

Feature:BEE Successfully Updated screen 2

Ticket: https://sero-digital.atlassian.net/browse/IES-979

Scenario:Click back button
6

Given I am a BEE installer in a home 2s 187ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 274ms
heatingSystem meterType
Boiler with hot water cylinder inlineMeter

And I configure the BEE until "Firmware Updated" 21s 405ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

Given I am on the "bee successfully updated screen" < 1ms

When I go back to previous screen 48ms

Then I am on the "hot water source screen" < 1ms

Scenario:Move to check peripherals screen
6

Given I am a BEE installer in a home 2s 182ms

And the BEE is running on the latest firmware and the peripherals connected to the BEE are healthy 298ms
heatingSystem meterType
Boiler with hot water cylinder inlineMeter

And I configure the BEE until "Firmware Updated" 11s 997ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

Given I am on the "bee successfully updated screen" < 1ms

When I continue 55ms

Then I am on the "check peripherals screen" < 1ms

Feature:Heat flow meter 3

As an IES installer
I want to be able to select whether a heat meter has been installed on the hot water of heating circuit
In order to indicate what energy is being measured in the home.

Scenario:Add heat flow meter
8

Given I am a BEE installer in a home 2s 212ms

And I configure the BEE until "Configure Heat Flow Meter" 7s 251ms

Given I configure heat flow meter 292ms
heatFlowMeterCircuit installLocation deviceType
hot_water Living room sharky

When I continue and wait 1s 28ms

Then the BEE is configured 57ms

And the BEE configuration has rules 1ms

And the BEE configuration has devices 1ms

And the BEE configuration has schedules < 1ms

Scenario:Edit heat flow meter
8

Given I am a BEE installer in a home 2s 291ms

And I configure the BEE until "Configure Heat Flow Meter" 7s 412ms

Given I configure heat flow meter 210ms
heatFlowMeterCircuit installLocation deviceType
hot_water Living room sharky

When I edit the heat flow meter "Living room" 957ms
heatFlowMeterCircuit installLocation deviceType
heating Somewhere else sharky

Then the BEE is configured 54ms

And the BEE configuration has rules 3ms

And the BEE configuration has devices 2ms

And the BEE configuration has schedules 2ms

Scenario:Delete heat flow meter
8

Given I am a BEE installer in a home 2s 196ms

And I configure the BEE until "Configure Heat Flow Meter" 7s 105ms

Given I configure heat flow meter 397ms
heatFlowMeterCircuit installLocation deviceType
hot_water Living room sharky

When I delete the heat flow meter "Living room" 1s 107ms

Then the BEE is configured 83ms

And the BEE configuration has rules 1ms

And the BEE configuration has devices 1ms

And the BEE configuration has schedules < 1ms

Feature:Persist the Selected Heating System 3

Ticket: https://sero-digital.atlassian.net/browse/IES-1206

Scenario Outline:Go back to the heating system select screen to see the selected one persisted (Boiler Heating Zones)
7

Given I am a BEE installer in a home 2s 228ms

And I configure the BEE until "Configure Heating System" 9s 811ms

Given I choose from one of the heating systems on the list 159ms
HeatingSystem
Combi boiler

And I configure a new boiler heating zone 74ms

And I have selected all the devices in a boiler heating zone 165ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

When I go back 2 screens 89ms

Then I want to see the type of heating system that has previously been selected 43ms
HeatingSystem
Combi boiler

Scenario Outline:Go back to the heating system select screen to see the selected one persisted (Boiler Heating Zones)
7

Given I am a BEE installer in a home 2s 333ms

And I configure the BEE until "Configure Heating System" 9s 814ms

Given I choose from one of the heating systems on the list 93ms
HeatingSystem
Boiler with hot water cylinder

And I configure a new boiler heating zone 77ms

And I have selected all the devices in a boiler heating zone 167ms
zone TempDial TempSensor Relay Continue
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 1 true

When I go back 2 screens 94ms

Then I want to see the type of heating system that has previously been selected 42ms
HeatingSystem
Boiler with hot water cylinder

Scenario:Go back to the heating system select screen to see the selected one persisted (Heat Pump Heating Zones)
7

Given I am a BEE installer in a home 2s 17ms

And I configure the BEE until "Configure Heating System" 8s 844ms

Given I choose from one of the heating systems on the list 143ms
HeatingSystem
MasterTherm heat pump

And I configure a new heat pump heating zone 53ms

And I have selected all the devices in a heat pump heating zone 317ms
zone TempDial TempSensor TempSensorLocation
Whole Home Thermokon WRF06 - Living Room HC2 Living Room

When I go back 2 screens 183ms

Then I want to see the type of heating system that has previously been selected 68ms
HeatingSystem
MasterTherm heat pump

Feature:Plot and Project 1

As an IES installer
I want to be able to record a project name and plot number
So that I can link project name, plot number and address

Scenario:Set Project Name and Plot
5

Given I am a BEE installer in a home 2s 483ms

And I configure the BEE until "Plot" 4s 199ms

Given I am on the project and plot screen 789ms

When I set the project "Parc Hadau" and plot "Plot 5" 218ms

Then the project "Parc Hadau" and plot "Plot 5" is stored 1s 148ms

Feature:Reset BEE configuration 1

Scenario:Reset BEE configuration
9

Given I am a BEE installer in a home 2s 253ms

And I configure the BEE until "Firmware Check" 12s 164ms
heatingSystem hotWaterSystem meterType
Boiler with hot water cylinder System boiler inlineMeter

And I click the home button 64ms

And I configure the BEE until "Search BEE" 518ms

When I reset the bee configuration 1s 63ms

Then the BEE is configured 40ms

And the BEE configuration has rules 1ms

And the BEE configuration has devices 2ms

And the BEE configuration has schedules < 1ms

Feature:SearchMacAddress 2

Scenario:Valid mac addresss
4

Given I am a BEE installer in a home 2s 136ms

And I configure the BEE until "Search BEE" 547ms
meterType
currentTransformerMeter

When I enter a valid mac address 93ms

Then I see the mac succesfully found message 641ms

Scenario:Invalid mac address
4

Given I am a BEE installer in a home 2s 71ms

And I configure the BEE until "Search BEE" 736ms
meterType
currentTransformerMeter

And I enter the mac "0A:88:B3:43:AE:E7" 310ms

Then I see the mac search failure message 74ms

Feature:Search postcode 1

Scenario:Search postcode
4

Given I am a BEE installer in a home 2s 148ms

And I configure the BEE until "Search Address" 2s 236ms
meterType
currentTransformerMeter

When I enter the postcode "W1J 7NT" and choose one from the list 1s 733ms

Then The address "2 Barons Court Road, LONDON, ID1 1QD" is saved 129ms

Feature:Thermokon WRF06 can be selected as a temperature sensor for a heating zone 3

Ticket: https://sero-digital.atlassian.net/browse/IES-1152

Scenario:Select previously configured Thermokon WRF06 as temperature sensor and proceed
4

Given I am a BEE installer in a home 2s 285ms

And I configure the BEE until "Configure Heating Zone" 10s 981ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

When I have selected all the devices in a boiler heating zone 250ms
zone TempDial TempSensor Relay Continue success
Kitchen Thermokon WRF06 - Kitchen Thermokon WRF06 - Kitchen Relay 5 true false

Then I am on the "assign boiler heating zones summary screen" 1ms

Scenario:Thermokon WRF06 can only be assigned to one zone
4

Given I am a BEE installer in a home 2s 326ms

And I configure the BEE until "Configure Heating Zone" 9s 904ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

When I have selected all the devices in a boiler heating zone 150ms
zone TempDial TempSensor Relay Continue success
Kitchen Thermokon WRF06 - Kitchen Thermokon WRF06 - Kitchen Relay 5 true true

Then I cannot select the assigned WRF06 temperature sensor when configuring another zone 92ms
AssignedTempSensor UnassignedTempSensor1 UnassignedTempSensor2 UnassignedTempSensor3
Thermokon WRF06 - Kitchen Thermokon WRF06 - Living Room Thermokon WRF06 - Ground Floor Thermokon WRF06 - First Floor

Scenario:Thermokon WRF06 dial can be assigned as a Thermokon WRF06 sensor for the same zone
4

Given I am a BEE installer in a home 2s 115ms

And I configure the BEE until "Configure Heating Zone" 10s 670ms
heatingSystem TempDialLocation TempDialChannel TempDialAddress
Boiler with hot water cylinder Living Room C1 1
Ground Floor C2 2
First Floor C3 3
Kitchen C4 4

When I have selected all the devices in a boiler heating zone 95ms
zone TempDial TempSensor Relay Continue success
Living Room Thermokon WRF06 - Living Room Thermokon WRF04 - Living Room Relay 5 false false

Then I can select the WRFO6 temperature dial as the temperature sensor for the same zone 192ms
TempSensor
wrf04 - living_room
wrf06 - living_room
wrf06 - kitchen
wrf06 - ground_floor
wrf06 - first_floor

Feature:Select whether boiler or heat pump is fitted 6

Ticket: https://sero-digital.atlassian.net/browse/IES-852

Scenario:Go back to previous screen from select heating type
4

Given I am a BEE installer in a home 2s 293ms

And I configure the BEE until "Configure Heating System" 9s 358ms

When I go back to previous screen 50ms

Then I am on the "config thermokon wrf04 screen" 1ms

Scenario:default heating system dropdown value
4

Given I am a BEE installer in a home 2s 82ms

And I configure the BEE until "Configure Heating System" 9s 418ms

When I am on the screen to choose the heating system from the drop down list 18ms

Then the default will be Select 31ms

Scenario:cannot move to next screen without select a heating system
4

Given I am a BEE installer in a home 2s 216ms

And I configure the BEE until "Configure Heating System" 9s 479ms

When I do not make a selection from the 4 options in the drop-down list 1ms

Then I cannot progress to the next screen 3ms

Scenario Outline:Select heat pump
4

Given I am a BEE installer in a home 2s 102ms

And I configure the BEE until "Configure Heating System" 9s 79ms

When I choose from one of the heating systems on the list 178ms
HeatingSystem
MasterTherm heat pump

Then I am on the "assign heat pump heating zones summary screen" 1ms

Scenario Outline:Selecting either of the boiler options
4

Given I am a BEE installer in a home 2s 204ms

And I configure the BEE until "Configure Heating System" 9s 817ms

When I choose from one of the heating systems on the list 89ms
HeatingSystem
Combi boiler

Then I am on the "assign boiler heating zones summary screen" 1ms

Scenario Outline:Selecting either of the boiler options
4

Given I am a BEE installer in a home 2s 143ms

And I configure the BEE until "Configure Heating System" 9s 64ms

When I choose from one of the heating systems on the list 71ms
HeatingSystem
Boiler with hot water cylinder

Then I am on the "assign boiler heating zones summary screen" < 1ms

Feature:upload device id sticker 3

Ticket: https://sero-digital.atlassian.net/browse/IES-530

Scenario:Upload device id sticker successfully
4

Given I am a BEE installer in a home 2s 173ms

And I configure the BEE until "Upload BEE sticker" 1s 781ms

When an image is uploaded 100ms
filename
../playwright/src/fixtures/ies-installer/ponyo.jpg

Then it should be stored in the cloud and associated to a specific BEE 748ms

Scenario:Unhappy with image preview
5

Given I am a BEE installer in a home 2s 216ms

And I configure the BEE until "Upload BEE sticker" 1s 526ms

When an image is uploaded 126ms
filename
../playwright/src/fixtures/ies-installer/ponyo.jpg

When I am not happy with the photo 144ms

Then I am back to device upload page 30ms

Scenario:Change image and upload succeessfuly
5

Given I am a BEE installer in a home 2s 319ms

And I configure the BEE until "Upload BEE sticker" 1s 498ms

When an image is uploaded 165ms
filename
../playwright/src/fixtures/ies-installer/ponyo.jpg

When I change the image to upload 72ms
filename
../playwright/src/fixtures/ies-installer/logo.png

Then it should be stored in the cloud and associated to a specific BEE 951ms

generated by @cucumber-html-reporter